how to replace the bathroom faucet
A brand new faucet is a great way to update your bathroom and give it a whole new look. Whether you are redesigning the bathroom or need to exchange an old or leaky faucet, this is a relatively simple DO IT YOURSELF project that you can accomplish in a few hours. The important thing is to get a faucet that fits your sink, so you should eliminate the original faucet before buying a replacement.
Gather your tools and supplies. Replacing your bathrooms faucet is a straightforward job, but it does require a few tools that you’ll need to remove the old tap and install the new one. The tools you’re looking for include
- Adjustable wrench tool
- Basin wrench
- Bath towel
- Measuring tape
- Plumber’s tape
- Sponge or scrubber
- Bathroom cleaner or detergent
- Rag or cloth
- Fresh faucet (purchased after you eliminate the original)
Prepare your work area: Remove everything from underneath the sink. Create a towel below the pipes to guard the pride from water damage and mold. Place a bucket over the towel and under the faucet to catch any water that drips down.
You can even lay a garbage carrier down under the soft towel for even more security, or in place of the bucket.
Turn off the water: Locate the water shutoff valve for the bathroom sink. It should be under the drain, inside the vanity. Switch the valve to the right (clockwise) to close up the valve and shut off the water to the faucet
Depending on your plumbing, you could have a single water device for the complete faucet, or else you could have two separate regulators for the hot and cold water.
If you have trouble picking out the shutoff valve, you can make off the water supply to the whole line running to the bathroom sink.
Deplete the water: To remove excess water from the faucet also to relieve pressure prior to starting working, drain the pipes after you closed off the water. Start up all the faucets at the sink and keep them running until all the water has drained away
This will protect your sink, vanity, and floors from leaks and water damage, preventing water from spraying everywhere when you remove the tap.
How to Removing the Old Faucet
Disconnect the provision tubes. These usually are the tubes that attach the faucet to the water supply. Use typically the adjustable wrench to ease the nuts where typically the hoses affix to the normal water supply
Once you’ve lost the nuts with all the hammers, you can remove them all of those another way by palm.
Loosen the locknuts in order to take out the aged faucet
Use your hands or perhaps an adjustable wrench to loosen the nuts in addition to unthread them from the tailpieces. Turn them to type the left (counterclockwise) to release them. Remove the almonds as well as the washers from typically the tailpieces.
Once you’ve taken out the supply lines, almonds, and washers, the faucet will be loose. Support the faucet in both hands and pull it right out from the mounting holes. Get rid of the gasket if right now there is one and established it aside with typically the faucet.
Use the flashlight to be able to locate the nuts beneath the sink if you’re having difficulty locating them.
Clean the faucet holes. Together with a sponge or mild abrasive pad, scrub the particular mounting holes around typically the sink where the sink sits. Use soap in addition to water or your selected cleanser or detergent. Once the area is clean, wash it well, pat that dry, and let it air-dry completely.
To remove old sealant or silicone, dampen a sponge or even rag with mineral mood and wipe the location clean. Then rinse the location with clean water in addition to pat it dry.
Decide what form of faucet you have. Once you’ve removed the faucet from the increasing holes, you can physique out what hole settings you’re working with in addition to the faucet you want. There are three major types of faucets
Individual hole, where the sink may only have one gap for the faucet, plus the faucet will just about all be one simple item with a single handle.
Center-set, where there may be three holes in the sink and typically the one-piece faucet will possess separate handles controlling the hot and cold normal water.
Widespread or split-set, which often work with three-hole basins, but the spout in addition to two handles come in three separate pieces.
Obtain a new faucet. Just before you go to the particular home or hardware store for a new sink, determine the faucet you might have, look at your container hole configuration, and measure the distance between typically the holes to ensure you will get typically the right replacement faucet. Jot down the number of slots your basin has, the faucet which was on right now there, and the distance involving the holes.
If you want to replace your aged faucet with a new kind, you’ll have in order to replace the basin too.